# Heartbeat lost infrequently ~ every 10 minutes randomly

**URL:** <https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308>\
**Category:** Blue Robotics Software\
**Created:** [July 11, 2026, 1:56pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308 "2026-07-11T13:56:56Z")\
**Posts on this page:** 20\
**Page:** 1

<div class="post-metadata">

**Author:** ![LukeGriffin](https://avatars.discourse-cdn.com/v4/letter/l/f9ae1b/32.png) [@LukeGriffin](https://discuss.bluerobotics.com/u/LukeGriffin)\
**Post date:** [July 11, 2026, 1:56pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/1 "2026-07-11T13:56:57Z")

</div>

Hi all,

I’m losing heartbeats between my ROV and topside roughly once every 10 minutes, at random — sometimes more frequently othertimes less often. It happens both when the vehicle is idle and when operating.

**To try debig I have the current setup:**

- Raspberry Pi 4 + Blue Robotics Navigator, BlueOS
- Direct Ethernet cabele from Pi to laptop with power from battery
- Topside: [QGroundControl on Windows laptop]

**What I’ve already ruled out / tried:**

- Power: swapped to a different 5V 6A supply. `vcgencmd get_throttled` returns `0x0` even after a session with dropouts (checked without rebooting), so no undervoltage has been detected since boot.
- Swapped to a different flight controller board
- Fresh BlueOS install on a new SD card
- Connected laptop directly via Ethernet to rule out tether/network gear

**Key observation:** with nothing plugged into the Pi, it runs fine with no heartbeat loss. As soon as all peripherals are connected, the dropouts start. This makes me suspect one of the connected devices, but I’m not sure how to pin down which as its so inconsistent that when I plug them in one by one it may work fine but on other instances it may loose heartbeats again? I’ve also tried another windows laptop I had and the issue still occured so rules out my topside.

Any recommendations to help me me figure out the cause?

![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/2/8/28b79bbcf974e98ed1d06114ac87f4817c7cfc6c.png)

---

<div class="post-metadata">

**Author:** ![tony-white](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/tony-white/32/18385_2.png) [@tony-white](https://discuss.bluerobotics.com/u/tony-white)\
**Post date:** [July 11, 2026, 5:23pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/2 "2026-07-11T17:23:27Z")

</div>

Hi @LukeGriffin -

What version of BlueOS are you running? You should be on the latest stable, 1.4.3?

You can check out your tether connection quality with the tether diagnostics app - if you install this in BlueOS and share a screenshot of it, it may show that your connection has issues that cause your disconnects.

Can you share what you have plugged into the Pi? It is suspicious that dropouts start with all peripherals connected, I would suspect one of them is pulling more power or cpu usage than it should…

---

<div class="post-metadata">

**Author:** ![Jhans](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/jhans/32/18197_2.png) [@Jhans](https://discuss.bluerobotics.com/u/Jhans)\
**Post date:** [July 12, 2026, 10:03pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/3 "2026-07-12T22:03:56Z")

</div>

I have the same issue on my rov aswell. I have the latest stable BlueOS 1.4.3 and the latest firmware for the navigator. I also just installed a brand new navigator and SD card, since my Navigator suddendly died. I could not load any of the vehicle parameters, so i swapped to a new one and that fixed one issue.

I just had a test dive since i was happy with all the bench testing. I run a network test and got around 35-40mbit/s on both download and upload. When the rov went in the water it was fine for a few minute, but then started to get the MYGC 255 Heartbeat Lost alarm, lost manual control very frequently.

I used the network test function in BlueOS many times and I could see sometimes that it dropped below 10mbit/s. And next time it could be 35mbit/s.

What could be the issue here? Very frustrating…

---

<div class="post-metadata">

**Author:** ![tony-white](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/tony-white/32/18385_2.png) [@tony-white](https://discuss.bluerobotics.com/u/tony-white)\
**Post date:** [July 13, 2026, 1:52am UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/4 "2026-07-13T01:52:36Z")

</div>

Hi @Jhans -

Same answer! The tether diagnostic extension should shed some light on your issue, as well understanding what payloads you have connected .

In general, no firmware is actually running on the Navigator! The autopilot runs on the pi, and communicates to output devices on the PCB - so if replacing your Navigator fixed your issues in the past that was likely due to either a hardware failure or software issue…

I’ve also noticed that if I leave a vehicle for a very long period on Deck, it can struggle initially went entering the water. I theorize this is something to do with the black magic that the lx200 does to send ethernet over two wires, and the RF situation changing dramatically from what was stable when when the tether begins to unspool and be in a isolated RF environment. Generally it stabilizes pretty quickly and is normal in my experience, but maybe it’s continuing for you?

---

<div class="post-metadata">

**Author:** ![Jhans](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/jhans/32/18197_2.png) [@Jhans](https://discuss.bluerobotics.com/u/Jhans)\
**Post date:** [July 13, 2026, 9:55am UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/5 "2026-07-13T09:55:31Z")

</div>

![IMG_5521](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/7/1/71ebc0803548b0221452850b5946d06b5792be63.jpeg)

 ![IMG_5522](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/1/0/103005dd47e32ae4e667fc842423c564106e80bf.jpeg)These two first pictures is with the blue-blue/white pair.

I swapped to the orange pair, and got a much mote stable connection. Just had a complete wet test just now and it works perfectly. So the fix for me was to swap to another twisted pair on both FXTI.

Last two pictures is with the orange pair that works flawless.

The tether diagnostic tool is great! Thanks @tony-white

 ![IMG_5524](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/d/4/d45cb3a2c11f44913dcb1910c7dcd7a1a8281927.jpeg)

 ![IMG_5523](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/a/d/ad94a38074f4a168b719fcbb461f7b65c04bbeca.jpeg)

---

<div class="post-metadata">

**Author:** ![LukeGriffin](https://avatars.discourse-cdn.com/v4/letter/l/f9ae1b/32.png) [@LukeGriffin](https://discuss.bluerobotics.com/u/LukeGriffin)\
**Post date:** [July 13, 2026, 4:22pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/6 "2026-07-13T16:22:26Z")

</div>

I have the latest version of BlueOS.

 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/1/7/17397b6a538e534405bae08e3cfac88721bd67c1.jpeg)

Firmware versio 4.5.7 (STABLE).

I have the following plugged into my pi:

Leak Sensor, barometer, [relay](https://www.amazon.com/gp/product/B07D1W6M7W/?th=1) (for dvl, pin 15), lights, servo for camera, using 5V from servo rail to power an [inverter chip](https://www.digikey.ie/en/products/detail/texas-instruments/SN74AHCT125N/13506153?gclsrc=aw.ds&gad_source=1&gad_campaignid=20159040368&gbraid=0AAAAADrbLlim7BsJyXX-X789zdiJStsUc&gclid=CjwKCAjwmdLSBhANEiwAkREMN-EVJHwnMsuWJomr6rBZI4qQrIudGjjUUrWvG7OY_2v1ASdmzVrPJxoCmIoQAvD_BwE), using serial 1 to read a signal using GPIO 14 to read a 3.3V high low signal.

Had an issue today when driving th ROV i was loosing connection but still had video feed and could control the ROV in test tank.

 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/1/3/13ad4d3113ae5f48a1d4c2986a09afcb8a76a964.jpeg)

Got this when left idle, when tether diagnostics droppped it didnt loose connection sometimes and sometimes did

 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/3/0/30b21068207c01cc45fec5bf299f62f281d3867c.jpeg)  
 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/6/7/674b050c922f9090593f16a5aa6fede119551a27.jpeg)

Is this a connection issue as its causing connection loss but doesn’t loose video feed / control sometimes? It’s very intermitient and difficult to replicate as it’s so inconsistent.

---

<div class="post-metadata">

**Author:** ![tony-white](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/tony-white/32/18385_2.png) [@tony-white](https://discuss.bluerobotics.com/u/tony-white)\
**Post date:** [July 13, 2026, 5:02pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/7 "2026-07-13T17:02:53Z")

</div>

Hi @LukeGriffin

You should _not_ be on that “latest” version of BlueOS! I recommend you update to 1.4.3, the latest stable. There have been many more (beta) versions of BlueOs in the past 5 months! You’ll need to connect the vehicle to WiFi with internet via the icon in the upper right to update.

The graph when you were having issues shows seperation between blue and pink lines in the upper left - this indicates that one of the wires in the fathom-x tether wire does not have a good electrical connection. Those dropouts also indicate complete disconnections!

I’d recommend removing elements of the connection chain until you find the culprit - start by connecting the tether directly to your topside, not going through the slip ring or deck cable of a tether spoool? That’s after you get on 1.4.3 BlueOS stable of course!

---

<div class="post-metadata">

**Author:** ![LukeGriffin](https://avatars.discourse-cdn.com/v4/letter/l/f9ae1b/32.png) [@LukeGriffin](https://discuss.bluerobotics.com/u/LukeGriffin)\
**Post date:** [September 27, 2026, 3:43pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/9 "2026-09-27T15:43:06Z")

</div>

Hi @tony-white,

Thanks for the help, ROV has a stable connection again. To fix the tether diagnostics i switched to a different twisted pair (orange one). Now have a solid connection. Also updated to the most stable version.

 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/1/e/1e3336e91793aa8c2eed295172dfe25343dfe1d2.jpeg)

Above is some a control interface I’ve created for the ROV through pymavlink and works pretty good in physical tank tests we’ve conducted (above is simulation). Planning to implement pitch and roll controllers etc. Will post about this in a new thread when its fully complete and open sourced so other people can try it.

Thanks a million,  
Luke Griffin

---

<div class="post-metadata">

**Author:** ![tony-white](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/tony-white/32/18385_2.png) [@tony-white](https://discuss.bluerobotics.com/u/tony-white)\
**Post date:** [September 27, 2026, 5:20pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/10 "2026-09-27T17:20:23Z")

</div>

Hi @LukeGriffin -  
Glad to hear you got things working.  
As for your control interface, have you considered using [Cockpit](https://github.com/bluerobotics/cockpit)? You could embed your interface in an iframe and not need to run windows side by side. Cockpit has been developed from the ground up to make full customization easy, and it’s completely open source! You can even create custom [widgets](https://blueos.cloud/cockpit/docs/stable/usage/advanced/#do-it-yourself-widget)…

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [September 29, 2026, 12:43pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/11 "2026-09-29T12:43:48Z")

</div>

Hi @tony-white

We have been having similar issues with our BlueROV2. It seems to be happening most frequently during the deployment and recovery of the ROV. Reading through this thread, I have downloaded the tether diagnostics tool. Below is a screenshot of the recording I just took but I’m not entirely sure what I am looking at. We are running on BlueOS 1.4.3 stable.

 ![Tether diagnostics Screenshot](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/d/e/dee39bdffebc3ecd59d96fa52955f92092f06800.png)

Many thanks!  
James

---

<div class="post-metadata">

**Author:** ![tony-white](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/tony-white/32/18385_2.png) [@tony-white](https://discuss.bluerobotics.com/u/tony-white)\
**Post date:** [September 29, 2026, 3:41pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/12 "2026-09-29T15:41:11Z")

</div>

Hi @ROV-Sepiola -  
Welcome to the forums!  
You want the blue and people lines to be over 100, as pictured. If when you lift the ROV by it’s tether, the lines go to 0 as in your screenshot, the graph is illustrating that all connection is lost! This suggests a bad connection somewhere between the FXTI box and the Fathom-x in the vehicle. You could try switching the tether pair used, making the switch in the ROV enclosure and topside box to another pair like orange, brown, or green.

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [October 1, 2026, 10:44am UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/13 "2026-10-01T10:44:23Z")

</div>

Hi @tony-white

Many thanks for your reply! I have now swapped over the tether pair used from blue to orange, and have bench tested it and for now can’t replicate the fault so hopefully that is the answer! Will see what happens when we next use it in a few weeks time.

Thanks again for your help 🙂

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [October 5, 2026, 11:55am UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/14 "2026-10-05T11:55:23Z")

</div>

@tony-white

We have just completed a sea trial and everything was working as expected without any dropout with connection using the new orange tether pair. Many thanks again for your help!

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [October 21, 2026, 12:20pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/15 "2026-10-21T12:20:47Z")

</div>

Hi @tony-white

Unfortunately some bad news. We went out for our first survey since going out for our trial, and we had a reoccurrence of our previous issue.

I did not have the tether diagnostics tool running, so cannot say whether that was the fault. However, we ran through all the pre-flight checks as normal no issues, we use a hydraulic dive lift to then slowly lower the ROV into the water, and as happened previously, as soon as the ROV made contact with the water it lost connection.

I restarted the topside computer, everything was then working again. Managed to then successfully deploy the ROV and complete the survey, drove the ROV back to the dive platform. However then as soon as we started to raise the ROV back out of the water it lost connection again.

We have changed the tether pair, as mentioned above. I am now considering if there are any known issues with loss of connection when either entering or exiting the water. Could there potentially be a data spike with the video feed changing visually so much from topside to underwater or vice versa?

This is a repeat of the issues we were having before where it exclusively was happening during deployment and retrieval. When doing so the tether is completely clear (as in it is not coming in contact with the side of the vessel etc) so I am starting to wonder if it computer/data based rather than tether.

Any help would be greatly appreciated.

---

<div class="post-metadata">

**Author:** ![3dMB](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/3dmb/32/13905_2.png) [@3dMB](https://discuss.bluerobotics.com/u/3dMB)\
**Post date:** [October 21, 2026, 1:34pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/16 "2026-10-21T13:34:22Z")

</div>

@ROV-Sepiola Apologies if I am asking something you have previously mentioned, does your ROV have a DVL?

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [October 21, 2026, 2:58pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/17 "2026-10-21T14:58:02Z")

</div>

Hi @3dMB

No, we are running a standard BlueROV2 without any additional hardware or modifications. The only change that’s been done since purchase was swapping the tether pairs from blue to orange as above.

---

<div class="post-metadata">

**Author:** ![3dMB](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/3dmb/32/13905_2.png) [@3dMB](https://discuss.bluerobotics.com/u/3dMB)\
**Post date:** [October 21, 2026, 3:14pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/18 "2026-10-21T15:14:09Z")

</div>

ok, no worries.

---

<div class="post-metadata">

**Author:** ![tony-white](https://sea1.discourse-cdn.com/flex019/user_avatar/discuss.bluerobotics.com/tony-white/32/18385_2.png) [@tony-white](https://discuss.bluerobotics.com/u/tony-white)\
**Post date:** [October 21, 2026, 4:18pm UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/19 "2026-10-21T16:18:14Z")

</div>

Hi @ROV-Sepiola -  
Interesting result! Because restarting your computer fixed things until the vehicle came back out of the water, I suspect the Fathom-X, and not the software stack in any way. It is true that you get a bit more data as the vehicle enters the water and the video stream grows more complex - however the larger change is to the impedance conditions the tether is exposed to. Restarting the computer may have been unnecessary- simply power cycling the topside FXTI box was likely sufficient to let the homeplug module “recalculate” and find frequencies that worked for communication.

Not running the tether-diagnostic extension is a huge bummer - it should show this in real-time! If you can check that on your next deployment, and give power cycling the topside Fathom-x a try (not the whole computer) I think we’ll have some useful insights.

Can you also confirm what length tether you’re using?

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [October 22, 2026, 6:41am UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/20 "2026-10-22T06:41:07Z")

</div>

Hi @tony-white

We will hopefully be running another survey today. So I will ensure that the tether diagnostics extension is running this time! Then will take note of that if we get the same fault, and then if it does happen will power cycle the FTXI box and go from there.

Thanks very much for your suggestions and help!

---

<div class="post-metadata">

**Author:** ![ROV-Sepiola](https://avatars.discourse-cdn.com/v4/letter/r/f6c823/32.png) [@ROV-Sepiola](https://discuss.bluerobotics.com/u/ROV-Sepiola)\
**Post date:** [October 22, 2026, 11:49am UTC](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308/21 "2026-10-22T11:49:47Z")

</div>

Hi @tony-white

So, we went to run our survey and somewhat thankfully we had the exact same thing happen, however this time I had the tether diagnostic tool running! (When being lowered, as soon as it made contact with the water it disconnected).

 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/0/8/08f30dad97995150fc468cce53b6db32a0b6175f.jpeg)

So it seems that the tether wasn’t the issue? There was no drop showing on the graph when the vehicle disconnected (can see at the top showing vehicle no longer connected).

I then unplugged the FXTI box to power cycle. When plugging back in the laptop made the noise showing something had been connected, however the stream did not reconnect on Cockpit and I had the screen below on the tether diagnostics extension.

 ![image](https://us1.discourse-cdn.com/flex019/uploads/bluerobotics/original/3X/6/a/6a402d817b9b7592967fc08ce0db1f2717bf4110.jpeg)

I then restarted the computer, opened up Cockpit and everything was working again, and managed to completed the planned dive without issues (including when coming back onboard).

[Next page](https://discuss.bluerobotics.com/t/heartbeat-lost-infrequently-every-10-minutes-randomly/23308.md?page=2)
